Outdoor Cabinet 50"H X 25"D |

| ALUMISHIELD | Top cover, shades cabinet from the sun |
| HANDLES | Stainless steel - NEMA |
| RAILS | Fully adjustable & alodine coated |
| DOORS | Front and rear secured with three point locks and padlocking handles |
| VENTS | Front & rear, top & bottom, filters supplied |
The OD-50DX is the superior design in communication cabinets, being as rigid as steel
& yet noticeably lighter than the old heavy steel constructed cabinets. This is made
possible with our own aluminum recipe called ALUMIFLEX. The OD-50DX offers the protection
needed for any sever outdoor environment. The OD-50DX is constructed of .125 ALUMIFLEX
material, & comes with an additional .125 ALUMISHIELD top cover, thereby fully
protecting your equipment from falling ice and the sun's heat penetration. Ultimate
security is provided by a three point locking system, which utilizes a NEMA stainless
steel cabinets, the OD-50DX, made of ALIMIFLEX, will operate without affecting or being
effected by RF influences. Outdoor cabinets are becoming the alternative shelter solution
for today's complicated zoning requirements. So weather your installing a new shelter or
adding room to your existing one, the OD-50DX is the ultimate solution.
| SPECIFICATIONS |
GENERAL |
||||||||||||||||||||||||||||||||
| Weight: 120 lbs. assembled 160 Lbs. Shipping weight |
||||||||||||||||||||||||||||||||
| Doors: Two - secured by three point locking system Locks via customer supplied padlocks sealed with 13/16" aluminum filled gaskets |
||||||||||||||||||||||||||||||||
| Material: .125 ALUMIFLEX Finish: Flat aluminum RF properties: Non-ferrous |
||||||||||||||||||||||||||||||||
| Vents: Twelve bottom louvers per door Six top louvers - in top cover under ALUMISHIELD One removable filter panel per door Six fixed filter pads in top cover |
||||||||||||||||||||||||||||||||
| Handles: Stainless steel | ||||||||||||||||||||||||||||||||
| Exterior Screws: Stainless with NEMA washers & nylon locking nuts | ||||||||||||||||||||||||||||||||
RACKING SPECIFICATIONS |
||||||||||||||||||||||||||||||||
| Rails: Two standard (For additional rails see accessories) Alodine coated Holes tapped to 10 x 32 threads Each rail supported by three R-STRUTS .125 material (ALUMIFLEX) |
||||||||||||||||||||||||||||||||
| Spacing: 19" EIA STANDARD | ||||||||||||||||||||||||||||||||
| Positioning: All rails fully adjustable from front to rear | ||||||||||||||||||||||||||||||||
| Useable Height: 50 inches | ||||||||||||||||||||||||||||||||
Useable Depth: Maximum: 21 1/2" Minimum: 19 3/4" (See
below)
*Section measurements start from the bottom of the cabinet (0.00") & runs vertically upward towards the top of the cabinet (50.00"): |
||||||||||||||||||||||||||||||||
DOOR OPENING CLEARANCE |
||||||||||||||||||||||||||||||||
| Width : 19 1/2 inches | ||||||||||||||||||||||||||||||||
| Height : 45 13/16 inches | ||||||||||||||||||||||||||||||||
EXTERIOR CABINET DIMENSIONS |
||||||||||||||||||||||||||||||||
| Main Body: Width: 25 1/2 inches Height: 50 1/4 inches Depth: 25 1/4 inches |
||||||||||||||||||||||||||||||||
| Alumishield: Width: 28 1/16 inches Hang down height: 1 3/4 inches Depth: 29 inches |
||||||||||||||||||||||||||||||||
| Handles: Handles: Protrude 1 7/8 inches |
||||||||||||||||||||||||||||||||
| Total Space Occupied: Width: 23 2/8 inches Height: 31 2/8 inches Depth: 25 1/4 inches |
||||||||||||||||||||||||||||||||
INSIDE CLEARANCE - LESS RAILS |
||||||||||||||||||||||||||||||||
| Width: 23 5/8 inches | ||||||||||||||||||||||||||||||||
| Height: 50 inches | ||||||||||||||||||||||||||||||||
| Depth: See racking spec's - useable depth chart above | ||||||||||||||||||||||||||||||||
REAR POWER CONNECTOR HOLE |
||||||||||||||||||||||||||||||||
| Hole size: One .858" diameter hole with two .142" mtg
holes / spaced 1.22" apart Description: Supports one male 7 pin power connector (allied part # T-3106-000 (weatherproof - male) mates with female 7 pin power connector (allied Part # T-648-000 (weatherproof - female)) Location : Under the rear apron, in the center of the rear panel |
||||||||||||||||||||||||||||||||
REAR RF CONNECTOR HOLES |
||||||||||||||||||||||||||||||||
| Holes Size: Two .641 diameter holes each with four .125"
mtg holes / spaced .718" sq. Description: supports two chassis mount type N or UHF con.'s Location : Both holes are located under the rear apron, one on the left side & one on right side of the rear panel |
RATINGS |
| NEMA: CLASS: 250 TYPE: 4 |
WARRANTY |
| Period: Two Years - Unconditional |
| R-2-50: Two extra 50" rails & mtg. hardware |
| MTDX: Mounting tray |
| CA-4: Caster Kit (4) & mtg. hardware |
| SCR-432: Rail Screws (4) 10x32 |
| P-DX: Powder baked on textured paint |
| Paint Tested: 500 Hour salt spray 500 hour immersion |
SHIPPING INFORMATION |
| The OD-50DX is shipped fully assembled, but can be easily knocked down and re-assembled at your site, if desired |