INDOOR CABINET 30"H X 25"D

ST-30DX

DESIGN Rounded Corners
PAINT Scratch resistant, textured, powder baked on.
RAILS Fully Adjustable & Alodine Coated
DOORS Front and rear doors secured with Non-Intrusion locks.
VENTS Front & rear filter panels


The ST-30DX is a new design in communication cabinets, being as rigid as steel & yet noticeably lighter than the old heavy steel constructed cabinets. This is made possible with our own aluminum recipe called ALUMIFLEX. The ST series are the most versatile cabinets in the market place today. Being designed for our continuously changing industry, the ST series is ahead of the competition in cost, weight and expansion capabilties. Any two of the ST (STACKABLE) series cabinets can be stacked one on top of the other (with our optional stacking kit). Weighing 53 lbs. & shipping knocked down, UPS will deliver this cabinet to your door for a fraction of the cost of our competitors' steel cabinets. Unlike the steel cabinets, our ST-30DX, made of ALUMIFLEX, will operate without affecting or being effected by RF influences. Order our ST-30DX, the new industry standard, and take care of todays needs while at the same time preparing for tomorrow's expansion requirements.


SPECIFICATIONS

GENERAL
Weight: 53 lbs.
Doors: Two - secured with non-intrusion locks
Locks and unlocks with a supplied set of keys
Designed to mount either left or right
Material: .1 ALUMIFLEX (our own aluminum recipe)
Finish: Grey, textured, powder baked on paint
RF properties: Non-ferrous
Vents: Two - 8" X 10" standard filter panel housings
One removable filter panel per door
Solid panels can be used for non ventiliation
Access Holes: One - One inch hole / with hole plug installed
Exterior Screws: Stainless with nylon locking nuts

RACKING SPECIFICATIONS
Rails: Two standard (for additional rails see accessories)
Alodine Coated
Holes drilled to accept tinnerman clips (see CL-4)
Each rail supported by two R-STRUTS
Material .125 ALUMIFLEX
Spacing: 19" EIA STANDARD
Positioning: All rails fully adjustable from front to rear
Usable Height: 30 inches
Useable Depth: Maximum: 24 11/16" Minimum 22 15/16" (See below)
*Section Starting
& Ending Points		 Vertical Height
Per Section		 Effective Depth
For each section
Top
 28.32" - 30.00"
19.00" -28.32"		 =
=		 1.68"
9.32"		 ...22 15/16"
...24 11/16"
Center 11.00" - 19.00"
1.68" - 11.00"		 =
=		 8.00"
9.32"		 ...24 3/16"
...24 11/16"
Bottom 0.00" - 1.68" = 1.68" ...22 15/16"
*Section measurements start from the bottom of the cabinet (0.00") & runs vertically upward towards the top of the cabinet (30.00"):

DOOR OPENING CLEARANCE
Width: 19 1/2 inches
Height: 26 3/4 inches

EXTERIOR CABINET SPECIFICATIONS
Main Body: Width: 23 1/4 inches
Height: 30 1/4 inches
Depth: 25 1/4 inches
Screws: Protrude 3/16" on each side
Total Space Occupied: Width: 23 5/8 inches
Height: 30 1/4 inches
Depth: 25 3/8 inches

INSIDE CLEARANCE - LESS RAILS
Width : 21 3/16 inches
Height : 30 inches
Depth : See racking spec's - useable depth chart above


RATINGS
NEMA: CLASS: 250
TYPE: 2
Paint Tested: 500 Hour salt spray
500 Hour immersion

WARRANTY
Period: Two years - Unconditional
ACCESSORIES
R-2-30: Two extra 30" rails & mtg. hardware
MTDX: Mounting Tray
CA-4: 4 - Caster kit & mtg. hardware
CL-4: 4 - tinnerman clips 10 x 24
SCR-4: 4 - rail screws 10 x 24
C-25": Trough top cover & 10" fan access
ST-ST30: Stacking kit (stack two ST-30's)
ST-ST3042 Stacking kit (stacks ST-30 & ST-42)

SHIPPING INFORMATION
The ST-30DX is shipped fully assembled, but can be easily knocked down and reassembled at your site, if desired